Skip to main content

Articles

19 result(s) within Volume 12 of International Journal of Mechanical and Materials Engineering

Page 1 of 1

  1. Renewable energy resources are becoming more important to meet growing energy demands while reducing pollutants in the environment. In the current market, wind turbines are primarily restricted to rural use du...

    Authors: Cory Seidel, Sanjay Jayaram, Leah Kunkel and Alexander Mackowski

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:19

    Content type: Original Paper

    Published on:

  2. The present exploration deliberates the effect of nonlinear thermal radiation on double diffusive free convective boundary layer flow of a viscoelastic nanofluid over a stretching sheet. Fluid is assumed to be...

    Authors: K. Ganesh Kumar, B. J. Gireesha, S. Manjunatha and N. G. Rudraswamy

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:18

    Content type: Original Paper

    Published on:

  3. The gouging torch process using air carbon arc cutting (CAC) device is a standard maintenance procedure carrying out in high-tonne equipment used in the minery industry. The application of this process could l...

    Authors: H. Ochoa Medina, J. Leiva Yapur, O. Fornaro and Z. Cárdenas Quezada

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:16

    Content type: Original Paper

    Published on:

  4. Vanadium alloy is one of the potential candidate material for structural applications in a commercial fusion reactor. Extended survival of a structural material has a direct consequence on the net energy produ...

    Authors: Vinoadh Kumar Krishnan and Kumaran Sinnaeruvadi

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:14

    Content type: Original Paper

    Published on:

  5. One of the current problems in studying the mechanical properties and behavior of structurally inhomogeneous media with cracks is the characterization of acoustic wave propagation. This is especially important...

    Authors: Elena L. Kossovich, Alexey V. Talonov and Viktoria L. Savatorova

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:13

    Content type: Original Paper

    Published on:

  6. Side-impact collisions represent the second greatest cause of fatality in motor vehicle accidents. Side-impact airbags have been installed in recent model year vehicle due to its effectiveness in reducing pass...

    Authors: D. Bendjaballah, A. Bouchoucha, M. L. Sahli and J-C. Gelin

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:12

    Content type: Original Article

    Published on:

  7. Impedance pump is a simple valveless pumping mechanism, which transports fluid through the mismatch of impedance in the system. Mismatch in impedance occurs when an asymmetrical periodic excitation is exerted ...

    Authors: V. C. C. Lee, Y. A. Abakr and K. C. Woo

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:11

    Content type: Original Article

    Published on:

  8. Strain and stress conditions in sheet metal shearing are of interest for calibration of various fracture criteria. Most fracture criteria are governed by effective strain and stress triaxiality.

    Authors: E. Gustafsson, S. Marth, L. Karlsson and M. Oldenburg

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:10

    Content type: ORIGINAL ARTICLE

    Published on:

  9. The purpose of the study is to investigate the effects of variable fluid properties, the velocity slip and the temperature slip on the time-dependent MHD squeezing flow of nanofluids between two parallel disks...

    Authors: K. Vajravelu, K. V. Prasad, Chiu-On Ng and Hanumesh Vaidya

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:9

    Content type: Original Article

    Published on:

  10. The Saint-Venant problem for porous elastic cylinders is of interest both from the technical and mathematical point of view. The intended applications of solution are to mechanics of bone and to some engineeri...

    Authors: D. Ieşan

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:8

    Content type: ORIGINAL ARTICLE

    Published on:

  11. This paper presents a numerical study of heat transfer inside the adsorber-collector of a solar adsorption refrigerator using the activated carbon AC35-methanol pair. The objective is to estimate the amount of...

    Authors: Noureddine Cherrad, Adel Benchabane, Lakhdar Sedira and Amar Rouag

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:7

    Content type: Original Article

    Published on:

  12. The austenitic stainless steel 304L is widely used as a structural material for which the finished surface has significant effect on the service performance. A study of the grinding process with regard to the ...

    Authors: Nian Zhou, Ru Lin Peng and Rachel Pettersson

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:6

    Content type: Original Article

    Published on:

  13. In rubber elastic models it is generally assumed that the bulk modulus is infinite, resulting in a material that does not change its volume and a pressure that cannot be evaluated from the material model.

    Authors: Brice N. Cassenti and Alexander Staroselsky

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:5

    Content type: Original Article

    Published on:

  14. Attractive properties of TRIP-type bainitic ferrite (TBF) steel ascribe to its unique microstructure of lath structure bainitic ferrite matrix and interlath retained austenite films. This work is concerned wit...

    Authors: Hoda Nasr El-Din, Ezzat A. Showaib, Nader Zaafarani and Hoda Refaiy

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:3

    Content type: Original Article

    Published on:

  15. The effect of β annealing on high cycle fatigue (HCF) and fatigue crack propagation (FCP) behaviors of Ti64 alloy were examined, and the results were compared to those of mill-annealed counterpart.

    Authors: Daeho Jeong, Yongnam Kwon, Masahiro Goto and Sangshik Kim

    Citation: International Journal of Mechanical and Materials Engineering 2017 12:1

    Content type: Original Article

    Published on:

COVID-19 and impact on peer review

As a result of the significant disruption that is being caused by the COVID-19 pandemic we are very aware that many researchers will have difficulty in meeting the timelines associated with our peer review process during normal times.  Please do let us know if you need additional time. Our systems will continue to remind you of the original timelines but we intend to be highly flexible at this time.

Annual Journal Metrics - 2020

Latest Tweets

Your browser needs to have JavaScript enabled to view this timeline