Skip to main content
Journal of Materials Science: Materials in Engineering
Journal of Materials Science: Materials in Engineering Cover Image

Articles

16 result(s) within Volume 14 of Journal of Materials Science: Materials in Engineering

Page 1 of 1

  1. Functionally graded material shafts are the main part of many modern rotary machines such as turbines and electric motors. The purpose of this study is to present an analytical solution of the elastic-plastic ...

    Authors: Shams Torabnia, Sepideh Aghajani and Mohammadreza Hemati
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:16
    Content type: Original Paper Published on:

  2. This paper studied the in-plane elastic stability including pre and post-buckling analysis of curved beams considering the effects of shear deformations, rotary inertia, and the geometric nonlinearity due to l...

    Authors: M. Zare and A. Asnafi
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:15
    Content type: Original Paper Published on:

  3. In this research, geometric parameters were given in dimensionless form by the Buckingham pi dimensional analysis method, and a series of dimensionless groups were found for deep drawing of the round cup. To f...

    Authors: Saeed Hajiahmadi, Majid Elyasi and Mohsen Shakeri
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:14
    Content type: Original Paper Published on:

  4. This review of MRF (magnetorheological fluids or MR fluids) brings out the challenges in methods of preparation, difficulties encountered in storage and use, and possible solutions to overcome the challenges.

    Authors: James Sathya Kumar, P. Sam Paul, Girish Raghunathan and Divin George Alex
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:13
    Content type: Review Article Published on:

  5. The present research deals with the propagation of Rayleigh wave in transversely isotropic magneto-thermoelastic homogeneous medium in the presence of mass diffusion and three-phase-lag heat transfer. The wave...

    Authors: Iqbal Kaur and Parveen Lata
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:12
    Content type: Original Paper Published on:

  6. The laminar 2-D blended convection of the nanofluids at different volume fractions has gained interest in the last decade due to an enormous application in technology. The laminar-flow stream system can be fur...

    Authors: Ali Assim Al-Obaidi, Ali J. Salman, Ali Raheem Yousif, Dalya H. Al-Mamoori, Mohamed H. Mussa, Tayser Sumer Gaaz, Abdul Amir H. Kadhum, Mohd S. Takriff and Ahmed A. Al-Amiery
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:11
    Content type: Original Paper Published on:

  7. The present research deals with the deformation in transversely isotropic thermoelastic (TIT) thin circular plate. Rotation effect is studied under thermally insulated as well as isothermal boundaries. The Lap...

    Authors: Iqbal Kaur and Parveen Lata
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:10
    Content type: Original Paper Published on:

  8. A progressive trend in instructional materials is the analytical plan and manufacture of fundamental operating equipment. LDPE/Gr nanocompounds were researched using various techniques such as Raman spectra (R...

    Authors: Maziyar Sabet and Hassan Soleimani
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:9
    Content type: Original Paper Published on:

  9. Experimental studies have been carried out to establish the possibility of using vibratory machining technology through shock-wave transmission for oxide coating preparation on aluminum-alloyed machine compone...

    Authors: Dieudonné Essola, Jean Chills Amba, Claude Valery Ngayihi Abbe, Joseph Nkongho Anyi and Vladimir Vitalevich Ivanov
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:8
    Content type: Original Paper Published on:

  10. The effectiveness of different methods, schemes, algorithms, and approaches is of substantial challenging problems in numerical modeling of transport phenomena. In the present paper, a lid-driven cavity proble...

    Authors: A. A. Boroujerdi and M. Hamzeh
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:7
    Content type: Original Paper Published on:

  11. The aim of this study was to establish the effect of cross bore configuration geometry on stress concentration in cross-bored high-pressure vessels. The cross bore geometry parameters with adverse effects on s...

    Authors: P. K. Nziu and L. M. Masu
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:6
    Content type: Review Article Published on:

  12. Stable and high surface area zirconium oxide nanoparticles have been synthesised by means of the hydrothermal method. The Brunauer–Emmett–Teller results show that a high surface area of 543 m2/g was obtained in t...

    Authors: Rudzani Sigwadi, Mokhotjwa Dhlamini, Touhami Mokrani and Fulufhelo Nemavhola
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:5
    Content type: Original Paper Published on:

  14. This study was conducted to investigate the synergistic effects of cutting parameters on surface roughness in ball end milling of oxygen-free high conductivity (OFHC) copper and to determine a statistical mode...

    Authors: Asiful H. Seikh, Biplab Baran Mandal, Amit Sarkar, Muneer Baig, Nabeel Alharthi and Bandar Alzahrani
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:3
    Content type: Original Paper Published on:

  15. This paper aimed to study the influence of zirconium phosphate (ZrP) nanoparticles on reducing the diameter of nanofibres during electrospinning. Addition of metal oxide such as zirconium phosphate decreases t...

    Authors: R. Sigwadi, M. S. Dhlamini, T. Mokrani and F. Nemavhola
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:2
    Content type: Original Paper Published on:

  16. In the machining operations, final surface finish and dimensional accuracy are the most specified customer requirements. Hard turning machining operation using cubic boron nitride tool as an alternative of gri...

    Authors: Sasan Yousefi and Mehdi Zohoor
    Citation: International Journal of Mechanical and Materials Engineering 2019 14:1
    Content type: Original Paper Published on:
Submit manuscript

COVID-19 and impact on peer review

As a result of the significant disruption that is being caused by the COVID-19 pandemic we are very aware that many researchers will have difficulty in meeting the timelines associated with our peer review process during normal times.  Please do let us know if you need additional time. Our systems will continue to remind you of the original timelines but we intend to be highly flexible at this time.

Follow

Annual Journal Metrics

Latest Tweets

Your browser needs to have JavaScript enabled to view this timeline

  • ISSN: 3004-8958 (electronic)